Yokohama Fender: What It Is, How It Works, Types, and Selection Guide
Introduction

Yokohama fenders
A Yokohama fender is a marine fender made of reinforced rubber layers and filled with compressed air. It protects vessels and docks by absorbing berthing impact energy through air compression.
The name comes from The Yokohama Rubber Co., Ltd., which developed this design in 1958. Over time, “Yokohama fender” became a widely used general term for pneumatic rubber fenders of this type. Today, fenders of this design are produced by many manufacturers and are used in ports, ship-to-ship (STS) operations, and offshore installations around the world. They are valued for high energy absorption, low reaction force, and flexible installation.
This guide covers the structure and working principle of the Yokohama fender, the main types, how to select the right size, and how to install and maintain it correctly.
What Is a Yokohama Fender?
A Yokohama fender is a reinforced rubber fender filled with compressed air. The term is used in two ways:
- As a brand name – genuine Yokohama-brand fenders are produced by The Yokohama Rubber Co., Ltd. and its authorised manufacturers.
- As a general term – many ports and buyers use “Yokohama fender” for any pneumatic rubber fender of this design, regardless of who makes it.
When requesting a quotation, it is best to specify the standard, performance requirements, and dimensions rather than relying only on the name.
Structure of the Rubber Body
1.Inner rubber liner
- An airtight layer that prevents air leakage.
- Usually made from halogenated butyl rubber because of its excellent air-retention properties.
2.Synthetic cord layers (tyre cords)
- High-strength nylon or polyester cords that bear internal pressure and impact loads.
- Multiple layers are wound at designed angles for balanced strength.
3.Outer rubber cover
- A wear-resistant layer exposed to seawater, UV, abrasion, and impact.
- Usually a blend of natural rubber and styrene-butadiene rubber (SBR).
4.Safety valve
- Releases pressure automatically if the internal pressure rises above the safe limit.
5.Protective covering (optional)
- Chain-and-tyre net, synthetic rope net, or polyurethane (PU) coating.
6.End fittings
- Shackles, chains, flanges, and lifting eyes for suspension and handling.

Yokohama type fenders
How Does a Yokohama Fender Work?
The working principle is based on air compressibility and can be broken down into three steps:
- Contact and deformation – The vessel presses against the fender, and the elastic rubber body deforms.
- Energy absorption – The air inside is compressed, and the pressure rises. The vessel’s kinetic energy is converted into gas compression energy and a small amount of heat. Because air compresses significantly, the fender deforms greatly while keeping reaction force relatively low.
- Rebound – After the vessel moves away, the compressed air and the elastic rubber return the fender to its original shape, ready for the next impact.
Performance reference (isothermal approximation):
E ≈ P₀ × V × ln(P₂ / P₀)
Where:
- P₀ = initial air pressure (commonly 50 kPa or 80 kPa)
- V = internal volume
- P₂ = maximum pressure after compression
This formula shows why larger fenders and higher initial pressure absorb more energy, and why the rubber body must be strong enough to contain the pressure safely.
Key Advantages
- High energy absorption, low reaction force – protects both hull and berth structure, especially for large vessels.
- Flexible installation – can be mounted on docks, suspended on ship sides, or used in STS operations.
- Adaptable – tolerates uneven berth surfaces, hull inclination, and tidal changes.
- Durable in marine environments – when made with the correct rubber compound, it resists seawater, UV, and abrasion.
- Reusable and repairable – minor rubber damage can often be cold-bond repaired.
Common Types of Yokohama Fenders
| Type | Protective covering | Typical application |
| Type I - Chain & tyre net | Heavy-duty chain and tyre protection | Large ports, STS, heavy berthing |
| Type II Rope net | Synthetic rope net | Vessel-mounted, medium duty |
| Net-less (slender type) | PU coating or rubber only | Light duty, clean quays, yacht berths |
| Floating type | Suspended to float on water | STS, floating docks, tidal areas |
Note: “Floating” describes how the fender is deployed, while Types I, II, and net-less describe the protective covering. These categories overlap.
Common Applications
- Large vessel berthing – oil tankers, LNG carriers, bulk carriers, container ships
- Ship-to-ship (STS) transfer – cargo, bunkering, and offshore supply
- Floating docks and pontoons
- Ports with large tidal ranges
- Offshore platforms and wind-farm support vessels
- Naval, coastguard, and patrol vessels
How to Select the Right Yokohama Fender
Selection is usually based on the following five factors:
- Vessel size (DWT) – larger vessels need larger fender diameter and length.
- Berthing velocity – higher speed means more energy to absorb.
- Tidal range – determines suspension length.
- Hull type and dock structure – affects fender spacing and quantity.
- Initial pressure – usually 50 kPa (0.5 bar) for standard use and 80 kPa (0.8 bar) for heavy-duty use.
Most reputable suppliers calculate requirements according to ISO 17357, the international standard for pneumatic rubber fenders. Always ask for a calculation sheet or performance data before purchasing.
Common Size Reference
| Fender size (D x L) | Typical use |
| 500 x 1000 mm | Smalll boats, yachts |
| 1700 x 3000 mm | Medium vessels, tugs |
| 2500 x 5500 mm | Large vessels, STS |
| 3300 x 6500 mm | Very large crude carriers, large STS |
The table above is only a general guide. Actual selection must be based on berthing energy calculations.
Installation Tips
- Inflate the fender to the manufacturer’s recommended pressure before suspending it.
- Use certified chains, shackles, and wire ropes with a suitable safety factor.
- Keep the suspension balanced so the fender hangs vertically and the load is evenly distributed.
- For floating installations, leave enough suspension length so the fender can follow the tide.
- Place fenders opposite the vessel’s main contact points: usually near the bow, stern, and midship.
- For STS operations, follow OCIMF ship-to-ship transfer guidelines.
Maintenance and Inspection
- Before each operation – visual check for obvious damage and correct positioning.
- Monthly (high-use) or quarterly (normal):
Check air pressure with a calibrated gauge and top up if needed.
Inspect the outer rubber for cracks, cuts, bulges, and ozone cracks.
Check the chain or rope net for wear and loose fittings.
Test the safety valve.
- Annually – thorough inspection, including rubber thickness at wear points.
- Storage – keep in a shaded, dry place, away from oil, grease, chemicals, and sharp objects.
Signs you should replace or repair the fender:
- Air pressure drops quickly after inflation.
- Visible bulges or delamination.
- Deep cuts reaching the cord layer.
- A faulty safety valve that cannot be repaired.
With proper care, service life is typically 8–10 years.
Common Mistakes to Avoid
- Over-inflation – exceeds the design pressure and risks bursting.
- Under-inflation – reduces energy absorption and can cause the fender to bottom out.
- Ignoring the safety valve – a faulty valve removes the most important safety protection.
- Using the wrong net type – a heavy chain net on a small vessel can cause unnecessary wear.
- Skipping berthing calculations – guessing the size often leads to oversized or undersized fenders.
- Specifying only the name “Yokohama” – always also specify the standard, size, and performance data.
- Buying only on price – low price often means lower rubber quality and weaker cord layers.
Frequently Asked Questions
Q: What is a Yokohama fender?
A: It is a pneumatic rubber fender made of reinforced rubber layers and filled with compressed air. The name comes from Yokohama Rubber, which developed the design in 1958, and it is now widely used as a general term for this type of fender.
Q: Are all Yokohama fenders made by Yokohama Rubber?
A: No. Genuine Yokohama-brand fenders are made by The Yokohama Rubber Co., Ltd. and its authorised manufacturers. Many other manufacturers produce equivalent fenders of the same design, usually built to meet ISO 17357.
Q: What pressure should a Yokohama fender be inflated to?
A: Most manufacturers recommend 50 kPa (about 0.5 bar) for standard applications and up to 80 kPa (about 0.8 bar) for heavy-duty berthing. Always follow the product manual.
Q: What does ISO 17357 cover?
A: ISO 17357 is the international standard that specifies requirements for pneumatic rubber fenders, including performance, materials, testing, and marking.
Q: How long do Yokohama fenders last?
A: With correct inflation and regular inspection, service life is generally 8–10 years, depending on usage and environmental conditions.
Q: Can Yokohama fenders be used for ship-to-ship operations?
A: Yes. STS transfer is one of their most common applications. They are usually suspended between the two vessels during the operation.
Conclusion
A Yokohama fender combines reinforced rubber construction with compressed-air cushioning. It delivers high energy absorption with low reaction force and can be installed in many different ways, from fixed docks to ship-to-ship operations.
When buying, base your choice on vessel size, berthing conditions, tidal range, and ISO 17357 calculations, not only on the name. Correct inflation, proper suspension, and regular inspection are the keys to long service life and reliable protection.
