
Nine types of pneumatic rubber fender
What Is a Pneumatic Rubber Fender?
A pneumatic rubber fender (also called a Yokohama fender) is a floating, air-filled marine fender made of reinforced rubber layers and synthetic tire-cord plies. It absorbs berthing energy between:
- Ship-to-ship (STS) transfers
- Ship-to-dock (STD) operations
- Offshore platforms, FPSOs, and naval vessels
Instead of crushing solid rubber, the fender compresses internal air—delivering high energy absorption with low reaction force, which protects both hull and quay.
All high-pressure units should be specified against ISO 17357-1:2014, with rated initial pressure of P50 (50 kPa) or P80 (80 kPa).
Why Fender Type Matters
Choosing the wrong type can cause:
- Premature abrasion or net failure
- Hull marking on sensitive coatings
- Insufficient energy absorption at high approach speed
- Higher maintenance and downtime
The “nine types” are not nine separate ISO classes—they are protective-cover and deployment variants built on Type I (net) and Type II (sling) bodies.
Nine Main Types of Pneumatic Rubber Fenders
1. Type I — Chain-Tire Net (Net-Type)
The most common heavy-duty pneumatic fender.
- Chain, wire, or fiber net with used truck tires
- Rubber sleeves protect the hull from chain contact
- Chain nets: corrosion-resistant; wire nets: lighter and easier to repair
Best for: STS oil/LNG transfers, VLCCs, permanent berths, rough seas
Pros: Long service life, high abrasion resistance
Cons: Heavy, can mark sensitive hulls
2. Type II — Sling-Type (Net-Free)
No external chain net. Thick outer rubber + lifting eyes at both ends.
- Lightweight and fast to deploy
- Direct rubber-to-hull contact
- Non-marking options available
Best for: Yachts, cruise ships, naval vessels, temporary berthing
Pros: Easy handling, low hull reaction
Cons: Less protection against sharp or abrasive surfaces
3. Type III — Ribbed Pneumatic Fender
Ribbed rubber humps on the fender body improve cushioning and stand-off.
- Middle ground between net-type and sling-type
- Better grip and impact distribution than flat sling fenders
Best for: Vessels needing extra contact control without full chain nets
4. Type IV — Rubber Mat & Rope Type
Uses rubber mats, marine ropes, and rubber tubes instead of steel-chain nets.
- Softer contact surface
- Reduced marking risk
Best for: Aluminum hulls, coated hulls, lighter commercial craft
5. Type V — Rubber Sleeve Net Type
Chain net fully covered by heavy-duty rubber sleeves.
- Synthetic-tire-cord-reinforced sleeves
- Common colors: black, orange
Best for: Clean-hull operations where chain abrasion is a concern
6. Type VI — Fiber Rope Net Type
Full coverage with reinforced marine fiber rope instead of chain.
- Lighter than chain-net units
- Multiple rope colors for identification
Best for: Moderate-duty berths, cleaner vessels, short-term projects
7. Type VII — Aircraft Tire Chain Net
Uses aircraft tires instead of automobile tires.
- Larger stand-off distance
- Better body protection under heavy compression
Grey/white non-marking rubber compounds are available for sensitive hulls.
Best for: Naval docks, submarine tenders, high-value hulls
8. Type VIII — Low-Pressure / Specialty Net Variants
Supplier-classified variants for low-pressure duty or custom netting layouts.
- Often built to ISO 17357-2 low-pressure concepts
- Custom rope/mat/hybrid protection
Best for: Custom berths, shallow-water platforms, specialized offshore use
9. Type IX — Vertical Hydro-Pneumatic Fender
Partially water-ballasted, installed vertically.
- Stays submerged for below-waterline contact
- Low hull pressure, high stability
Best for: Submarines, catamarans, semi-submersibles, low-freeboard vessels
Quick Comparison Table
| Type | Protection | Weight | Aluminum vessels |
| I Chain-Tire Net | Heavy | High | Clean hulls |
| II Sling | None | Low | Yachts, naval, temp use |
| III Ribbed | Medium | Medium | Coated hulls |
| IV Rubber Mat/Rope | Soft | Medium | Aluminum vessels |
| V Rubber Sleeve Net | Chain + sleeve | Medium-High | Clean hulls |
| VI Fiber Rope Net | Soft rope | Medium | Light commercial |
| VII Aircraft Tire Net | Heavy | High | Naval/submarine |
| VIII Specialty Net | Custom | Varies | Custom berths |
| IX Hydro-Pneumatic | Water ballast | High | Submarines, subsurfaced hulls |
How to Specify the Right Pneumatic Fender
Use this minimum purchase specification:
Pneumatic rubber fender, ISO 17357-1:2014, P50/P80, Ø × L mm, Type I/II, net configuration, safety valve, third-party class certificate (BV/ABS/DNV/CCS/LR)
Selection checklist
- Calculate berthing energy (PIANC method)
- Match GEA at 60% deflection
- Check reaction force vs hull pressure limit
- Choose P50 (sensitive hull) or P80 (heavy tanker)
- Choose net type (abrasion) or sling type (clean contact)
- Confirm safety valve for Ø ≥ 2500 mm
Maintenance Best Practices
- Check pressure monthly (±10% of rated)
- Inspect nets, tires, chains, and slings every 3–6 months
- Rinse with fresh water after heavy fouling
- Store deflated, shaded, away from ozone/heat
- Service valves regularly
Typical service life: 6–15 years with proper care.
FAQ
Q: Are Yokohama fenders and pneumatic rubber fenders the same?
Yes. “Yokohama type” is the generic trade-origin name; “pneumatic rubber fender” is the ISO technical term.
Q: What is the difference between P50 and P80?
P50 = 50 kPa initial pressure, lower reaction. P80 = 80 kPa, higher energy absorption. Never overinflate a P50 body to P80.
Q: Which type is best for ship-to-ship transfer?
Type I chain-tire net, usually P80, for heavy tankers. Sling type for lighter/clean hulls.
Q: What is a hydro-pneumatic fender used for?
Submarine berthing and vessels with hull contact points below the waterline.
Final Takeaway
The nine main types of pneumatic rubber fenders give buyers a clear way to match protection level, hull sensitivity, and berthing energy to the right floating fender. For most heavy marine operations, Type I net-type wins. For clean, fast, sensitive hulls, Type II sling-type is best. For submerged contact, Type IX hydro-pneumatic is the only correct choice.
