Floating Pneumatic Rubber Fender: What It Is, How It Works, and How to Select the Right One
Introduction

Floating Pneumatic Rubber Fenders
A floating pneumatic rubber fender is a marine fender made of reinforced rubber layers and filled with compressed air. It floats on the water surface and absorbs the impact energy between a vessel and a dock or another ship.
Because it floats, it rises and falls with the tide. This makes it the preferred choice for ship-to-ship (STS) transfer, floating docks, and ports with large tidal ranges.
This guide covers the structure of the rubber body, how the fender works, the main types, how to select the right size, and how to install and maintain it.
What Is a Floating Pneumatic Rubber Fender?
The term has three parts, and each matters:
- Rubber – the fender body is built from several layers of specialised rubber and reinforced cord.
- Pneumatic – the inside is filled with compressed air, which acts as the cushioning medium.
- Floating – the fender is suspended so that it stays on the water surface and moves with the tide and the vessel.
The structure of the rubber body usually includes the following layers:
- Inner rubber liner – an airtight layer that prevents air leakage. It is commonly made from halogenated butyl rubber because this material has excellent air retention.
- Synthetic cord layers – high-strength tyre cord, such as nylon or polyester, that bears the internal pressure and impact loads.
- Outer rubber cover – the wear-resistant layer exposed to the environment. It is normally made from a blend of natural rubber and styrene-butadiene rubber (SBR) for abrasion resistance and resilience.
- Optional protective coverings – a chain-and-tyre net, a rope net, or a polyurethane (PU) spray coating for extra protection.
Why rubber? Rubber combines elasticity, seawater resistance, and impact absorption in a way that rigid materials cannot match. The pneumatic design then adds the compressibility of air, so the fender absorbs large amounts of energy while keeping reaction force low.

Floating Pneumatic Fenders
How Does a Floating Pneumatic Rubber Fender Work?
The working principle is based on air compressibility and can be broken down into three steps:
- Contact and deformation – The vessel presses against the fender, and the elastic rubber body deforms.
- Energy absorption – The air inside is compressed and the pressure rises. The vessel’s kinetic energy is converted into gas compression energy and a small amount of heat. Because air compresses significantly, the fender deforms greatly while keeping reaction force relatively low.
- Rebound – When the vessel moves away, the compressed air and the elastic rubber return the fender to its original shape, ready for the next impact.
Performance reference (isothermal approximation):
E ≈ P₀ × V × ln(P₂ / P₀)
Where:
P₀ = initial air pressure (commonly 50 kPa or 80 kPa)
V = internal volume
P₂ = maximum pressure after compression
This shows why larger fenders and higher initial pressure absorb more energy. It also explains why the rubber body must be strong enough to contain the higher pressure safely.
Key Advantages
- High energy absorption, low reaction force – protects both the vessel hull and the dock or adjacent ship.
- Movable with the tide – ideal for locations with large water-level changes.
- Excellent elasticity – rubber returns to shape after repeated compression.
- Easy to relocate – can be transferred between vessels or berths.
- Adapts to hull shape – suits uneven berth surfaces and inclined hulls.
- Durable in marine environments – when made with the correct rubber compound, it resists seawater, UV, and abrasion.
Common Applications
- Ship-to-ship (STS) transfer – oil, LNG, bulk cargo, and marine fuel (bunkering) operations
- Floating docks, pontoons, and temporary berths
- Ports with large tidal ranges
- Offshore platforms and wind-farm support vessels
- Naval, coastguard, and patrol vessels
- Ro-Ro and ferry terminals
Types of Floating Pneumatic Rubber Fenders
| Type | Protective covering | Typical use |
| Type I | Chain and tyre net | Heavy-duty STS and large-vessel berthing |
| Type II | Synthetic rope net | Vessel-mounted fendres, medium duty |
| Net-less (slender type) | PU coating or rubber-only | Light duty, clean quays, and yacht berths |
Some manufacturers also offer foam-filled versions. These cannot deflate, but they are not strictly pneumatic because they do not rely on air compression.
How to Select the Right Floating Pneumatic Rubber Fender
Selection is normally based on the following five factors:
- Vessel size (DWT) – larger vessels need larger fender diameter and length.
- Berthing velocity – higher speed means more energy to absorb.
- Tidal range – determines the length of the suspension chains or ropes.
- Hull type and dock structure – affects fender spacing and quantity.
- Initial pressure – usually 50 kPa (0.5 bar) for standard use and 80 kPa (0.8 bar) for heavy-duty applications.
Most reputable suppliers calculate requirements according to ISO 17357, the international standard for pneumatic rubber fenders. Always ask for a calculation sheet before purchasing.
Installation Tips
- Inflate the fender to the pressure stated in the manufacturer’s manual before use.
- Use certified chains, shackles, and wire ropes with a suitable safety factor.
- Make sure the suspension points are evenly loaded and the fender hangs vertically.
- Leave enough suspension length so the fender can follow the tide.
- Place fenders opposite the vessel’s main contact points, usually near the bow, stern, and midship.
- For STS operations, follow the guidelines in OCIMF ship-to-ship transfer guides.
Maintenance and Inspection
Regular maintenance directly affects service life. A typical schedule looks like this:
- Before each operation – visual check for obvious damage, and confirm the fender is correctly positioned.
- Monthly (high-use sites) or quarterly (normal sites):
Check air pressure with a calibrated gauge and top up if needed.
Inspect the outer rubber for cracks, cuts, bulges, and ozone cracks.
Check the chain or rope net for broken links, wear, and loose fittings.
Test the safety valve.
- Annually – a more thorough inspection, including checking the rubber thickness at wear points.
- Storage – keep the fender in a shaded, dry place, away from oil, grease, chemicals, and sharp objects.
Signs you should replace the fender:
- Air pressure drops quickly even after inflation.
- Visible bulges or delamination of the rubber layers.
- Deep cuts that reach the cord layer.
- A damaged safety valve that cannot be repaired.
With proper care, a floating pneumatic rubber fender typically lasts 8–10 years.
Frequently Asked Questions
Q: What is the difference between a floating pneumatic rubber fender and a Yokohama fender?
A: They refer to the same product family. “Yokohama fender” comes from the company that first developed the pneumatic fender in 1958, while “floating pneumatic rubber fender” describes its structure and how it is used.
Q: What rubber materials are used in these fenders?
A: The inner liner is commonly halogenated butyl rubber for air retention. The outer cover usually blends natural rubber with SBR for abrasion resistance, and the reinforcement uses nylon or polyester cord. Exact compounds vary by manufacturer.
Q: Can floating pneumatic rubber fenders be used for ship-to-ship operations?
A: Yes. STS transfer is one of their most common uses. They are suspended between two vessels and absorb impact as the vessels move alongside each other.
Q: How much air pressure should I put in a floating pneumatic rubber fender?
A: Most manufacturers recommend 50 kPa (about 0.5 bar) for standard use and up to 80 kPa (about 0.8 bar) for heavy-duty berthing. Always follow the product manual.
Q: What does ISO 17357 cover?
A: ISO 17357 is the international standard that specifies requirements for pneumatic rubber fenders, including performance, materials, testing, and marking. It is the main reference for selection and procurement.
Conclusion
A floating pneumatic rubber fender combines reinforced rubber construction with compressed-air cushioning. It floats on the water, follows the tide, and protects vessels and docks with high energy absorption and low reaction force.
When buying, base your choice on vessel size, berthing conditions, tidal range, and ISO 17357 calculations. Correct inflation, proper suspension, and regular inspection are the keys to long service life and reliable protection.
